ESPOD ES-2444C is a best-in-class 802.11n indoor access point designed specifically for business-class environments such as hotels, airports, coffee shops, shopping centers, sporting venues, and university campus. With transfer rates of up to 300Mbps in the 2.4 GHz frequency range, the device provides an adequate level of service to all users who connect with legacy 802.11b/g adapters in addition to the latest 802.11n adapters for faster downloads and instant communication. Integrated Power over Ethernet (PoE) allows installation in areas where power outlets are not readily available. Internally equipped with 2X2 multiple-input, multiple-output (MIMO) antennas improve range and maximize data rates. Field tested to wirelessly cover 8-10 hotel rooms at an indoor operating distance of 40-50 meters and allow simultaneous accesses by up to 30 users.
Housed in a stylish ceiling mountable case, the ES-2444C can be installed on a wall or ceiling just as a ceiling lamp and blends in nicely with most interior decorations in a modern hotel. Installed highly on ceiling, it extends optimum wireless signal to multiple neighboring rooms.
High Power and Whole Coverage
With 500mW high power, Internally equipped with 2X2 multiple-input, multiple-output (MIMO) 5dBi Airgain antennas improve range and maximize data rates. Field tested to wirelessly cover 8~10 hotel rooms at an indoor operating distance of 60 meters and allow simultaneous accesses by up to 57 users. Up to 300Mbps wireless rate ensures multiple users an adequate level of service.
Power over Ethernet
The device has integrated Power over Ethernet (PoE) for easy installation and lower cost, with 24V passive PoE, it can be installed in areas where power outlets are not readily available, eliminating the mess of altering existing network infrastructure.
VLAN and Access Controller System
This ES-2444C comply with 802.1Q standard, it create a separate, secure, password protected network for guests.
With Access Control System, easily access advanced network settings through PC, like AP status monitor, change IP address, ESSID, Channel, Password, upgrade firmware, backup and restore….
Work with AP Address Server, can be assigned IP address auto when power on!
| Specification | |||
| Hardware | |||
| MCU | MTK 7620A | ||
| RF | 2T2R, 300Mbps MIMO tech , comply with IEEE 802.11N standard | ||
| Memory | 64MB DDR RAM | ||
| Flash | 8MB | ||
| Interface | 2 x RJ-45 for 10/100 Mbps WAN/LAN Port (Support 12V/24V POE) | ||
| 1 x Reset button(Reset & Factory Defaults) | |||
| 1 x Power DC Jack | |||
| Power | 12V(POE 12V/24V)/1A; or 802.3af, 48V PoE, 110V/220V | ||
| Antenna | Build in 2PCS Omni 5dbi antenna | ||
| Size | 16.8*4.5CM | ||
| RF | |||
| Frequency | 802.11b/g/n, 580MHz | ||
| 2.4~2.4835GHz | |||
| U.S.,Europe and Japan product covering 2.400 to 2.4835 GHz,programmable for different country regulations | |||
| Modulation | OFDM = BPSK,QPSK, 16-QAM, 64-QAM | ||
| DSSS = DBPSK, DQPSK, CCK | |||
| Throughput | 300 Mbps | ||
| Sensitivity | 802.11n(2.4GHz) | 802.11g | 802.11b |
| -90dBm @ MCS0 | – 90dBm @ 6Mbps | – 95dBm @ 1Mbps | |
| -70dBm @ MCS7 | – 72dBm @ 54Mbps | – 90dBm @ 11Mbps | |
| -90dBm @ MCS8 | |||
| -68dBm @ MCS15 | |||
| Output Power | Radio1(WLAN1) | ||
| 802.11n(2.4GHz)(± 1.5dBm) | 802.11g(± 1.5dBm) | 802.11b(±1.5dBm) | |
| 24dBm@ MCS0~2/MCS8~10 | 24dBm @ 6~24Mbps | 27dBm @1~11Mbps | |
| 24dBm @ MCS3/MCS11 | 24dBm @ 36Mbps | ||
| 24dBm @ MCS4/MCS12 | 24dBm @ 48Mbps | ||
| 24dBm @ MCS5/MCS13 | 24dBm @ 54Mbps | ||
| 24dBm @ MCS6/MCS14 | |||
| 24dBm @ MCS7/MCS15 | |||
| Software | |
| Operation Mode | Gateway/ AP/ Repeater |
| Protocol/Standard | IEEE 802
|
